Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode
How to enter test mode on Beko wmb 7, 8, 9 Series washing machines diagnostic & test mode to repair faults and test errors
Beko Diagnostic
Important notice on Beko
Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:
This video can be used on all these makes
WMB81431LW, WMB71231B, WMB61631W, WM5141W, WM5141S, WMB71422S, WMP601W, WMP541W, WMB81241LS, WML72S, WASH814DW, WMC6100W, WMB61021W, WMB71642S, WMB61431W, WMC6140W, WMB71021W, WMB61631S, WMB81241LB, WML72B, WMP652W, WMP631S, WM74135W, WMB61221S, WMB71231S, WM74155LW, WM74155LS, WMB61431S, WMB51221W, WM622W, WMB61431B, WMD61W, WMB51221S, WMP501S, WMB61221W, WM7355S, WMB81221LS, WMC6100S, WMB81241LW, WML72WXC, WMC6120W, WMB91242LB, WML15105D, WM5100W, WME8227W, WMB71442W, WM85135LW, WME7227W, WME7247W, WM5100S, WMC62W, WM6123W, WME7267W, WMC61W, WM6103W, WM6123S, WME7227S, WM6167W, WME8227S, WM5121W, WM6111W, WMP621W, WM612W, WM6355W, WME7247S, WMC61S, WM5121S, WM6167S, WME7267S, WM7335W, WME8227B, WMB91242LC, WMI71641, WMI7462, WMI71441, WMB71231W, WME7227B
Test Mode Sequence
If you have problems with the drum not turning or spinning. Then check the carbon brushes in the motor first and test the motor separately before running this Diagnostic sequence as you could do damage to the PCB.
To enter test mode.
It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode
With the machine switched off shut the door and turn the dial to the 12 o'clock position. Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds until the display shows a number or error code.
Now that you've entered the Diagnostic / test mode, remember every time you press the start/pause button this will be one advance the program to a new test.
- 1: All the the display or led’s will flash to check that they are working and door will now be locked.
- 2: Drum does a clockwise rotation.
- 3: Drum rotates anticlockwise rotation
- 4: Goes into spin mode on clockwise rotation make sure there are no clothes in machine before performing this test as washer will spin at its fastest rpm.
- 5: right hand water valve check
- 6: left hand water valve check
- 7: both water valve are now activated and all 3 compartments will have water flowing in.
- 6: This is the full wash and heat test. Machine will start to fill to the correct water level and continue to heat and wash.
- 7: the machine will empty. the pump should drain the water away.
- 8:After it has finished turn the machine off and on this will go back to normal mode.
-
How to Unblock or Replace Beko Washing Machine Pump
-
How to replace Beko Washing Machine Motor Carbon Brushes
-
Beko washing machine not filling with water Error code E08
-
How to Replace Beko washing Machine Door Seal
-
Beko WM5100W & WM5100S test mode and error codes
-
Beko WM6143B, WM6143S, WM6143W test mode and error codes
Hi there,
Having an issue with my Beko WMB 81241LW. It seems to be stuck in a cycle and won’t progress. ive done the self test and the only code the display is showing is 1518. During self test it performs steps 1 & 2 fine then it just wont progress any further and is making a slight buzzing noise. Any help appreciated!
I’ve had code F13
Then 04 06 on beko WM 95135 LB
I’ve tried doing the self diagnostic test. My washer skips the spin part but does all the rest.
When I turn it on normally to try and test it starts to fill and then drains and just keeps doing this, doesn’t go any further, any ideas before expensive repair from beko
Mine is doing the same thing. does anyone know a solution?
Washing machine not working fault no E11 ON SCREEN
I have ,E11 come up when l did the test. What do l do now please
boa tarde eu tenho uma maquina de lavar BEKO WMB 91242LC o código de erro e E18 o que poderei fazer ja tentei impar o codigo mas nao faz nada obrigado
boa tarde eu tenho uma maquina de lavar BEKO WMB 91242LC o código de erro e E18 o que podes fazer mais tentei com o mais fácil de usar.
nao consigo fazer o reset obrigado
Hi there I have problem with my beko washing machine wmb91442lw xl9 the problem that it’s not spinning I’ve done diagnostic test mode on it everything works please can you give some advise thank you.
My Beko washing machine comes up with error 0428. What does that mean?
My machine keeps showing E–. What does this mean. It does not give a number just two lines after the E. I find if I rotate the settings to the right to cottons I get this error, but if I rotate to the left all the way round to the same cottons setting then it shows the timer and allows the wash. It is so strange that the direction I turn the dial has different results.
I have had the machine for approx 4 years and it never used to do this. It only started over the last week.
If is the same for any wash, just does not like clockwise for some reason.
The machine seems to be stuck in a quick wash program. The test starts with the notice E18.
?hat fault is this and how can I fix it please?
I need.to change the motot
My Beko WM71641 built in, front loading washing machine is working but leaks towards the end of the cycle. I have twice run an empty cleaning cycle to clear the pipes but the machine still leaks. I have drained the water out of the machine and found nothing in the water. Any advice as to how to best approach the problem. My son should be able to follow any videos – or would you recommend I call an appliance repair technician.
I have a wm74135w beko how do I enter the diagnostics as no tutorial seems to cover this model
Beko xl9 Start light is flashing but no padlock shows, can open door.
Programme is stuck on 800 spin, 40 degrees and 1:15
Pressing start and on at the same time gives error code F02
Displays changes to spin 1880 (too many) and every other function light is on but nothing happens
Please help?
Thank you
I have a Beko WMB 81241 LW which shows a fault code E10. What is this please?
Hoping you can help please.
Many thanks. Paul.
My machoe shows error EO2 what does this mean and is it fixable
i have becc washing machine type WMB60821 M NOT DRAINING THE WATER I TESTED THE PUMP OUT SIDE IT IS OK
i have BEKO Washing machine type WMB60821 M NOT DRAINING THE WATER I TESTED THE PUMP OUT SIDE IT IS OK
My beko wmb 71041 7kg can not start bring too 1st.when I sylect jinse wash 1000 spin and 70 digri temperature then I can play. But it’s machine play oviesly but it’s not running..
To read the error code you can also hold button 1. and 3. under the display while the machine is turned on. It doesn’t clear the error code, but only displays it. Works for Beko WMB 71242
I have beko wmb81431lw washing machine. Its heater element was dead, i have changed it to new, but heaters are not getting the power, i tried another pc board, then i changed the pressure switch, but its still the same, lastly i changed the inter lock but no power coming to heater element. Please let me know, what els to do ?
Hi There.
I have done it. It was little thermistor of heater element. Thanks